Home > Parts & Accessories > Engine
Choose a sub category:
Flathead Ford
Chevy & GMC Buick, Oldsmobile, & Pontiac
Cadillac Dodge, Chrysler, & Plymouth
Studebaker Ignition System
Engine Mounted Gauges Fuel System
Valve Cover Valley Cover
Motor Mounts & Brackets Intake Manifolds
Sort By:
Page of 2
Stromberg Premium Service Kit 97 Carbs 1932-34 FORD ZENITH CARBURETOR GASKET KIT Genuine Stromberg 97 Carburetor

*Will fit on your new or original stromberg carb*

*Will fit on your new or original stromberg carb*

Looking for a Stromberg 97 carburetor for your early Ford?
Some traditional hot rod carburetion, or maybe a replacement for your tired Holley 94s or ochesters? The original and Genuine Stromberg 97 carburetor is available only from Stromberg Carburetor. Built accurately to original Stromberg blueprint specification, but with a number of key improvements.
They’re just the same, but better than ever. Extensive dyno and road tests have proved that it matches or exceeds original spec. And all Stromberg service parts are interchangeable with the originals.


Stromberg Premium Jet Wrench Stromberg Superseat Hose Fitting Stromberg Hex Head Plug Chrome

*Will fit on your new or original stromberg carb*

*Will fit on your new or original stromberg carb*

*Will fit on your new or original stromberg carb*

Stromberg 1/4NPT Hose Fitting Chrome MOON Screw on Fuel Cap 2-1/4" Oldsmobile Center Bolt Valve Cover Adapters

*Will fit on your new or original stromberg carb*

2-1/4" weld on type bung.

Valve cover adapter (pair). Allows centerbolt small block chevy valve cover installation on early heads with flange bolt valve covers. Gaskets NOT included, but special bolts and spacers are.

Meziere Polished Water Pump SBC Serp Pulley 1949-1950 Fauxsmobile Valve Covers 1929-1953 Double Groove  Flathead Pulley
Slightly used, but in good condition. Serpentine belt rotation pulley Meziere Polished water pump for small block Chevy.

oldsmobile valve cover

DIMENSIONS: 6" Overall Diameter, 1-5/8" O.D., 1-3/8" I.D.
Oil Pump Pickup & Cover Assembly 1932-1948 Fuel Pump Push Rod 8.87" Downdraft Intake Double Carb 1928-1934
Ford Pickup Truck Oil Pump Pickup Tube - 239 Flathead V8
This length pushrod may also be required when using an aftermarket aluminum intake manifold.
Available in dual or triple versions. These are machined to accept the early V8 carbs. While they do look impressive they do deliver a good bit of fuel. For stock engine applications you are better off sticking with a single downdraft style of intake. Aluminum. U.S.A.
Downdraft Intake Triple Carb 1928-1934 Alternator Pulley 9/16" 1932-1939 Ford & Mercury 1942-1948 Double Groove Flathead Pulley
These are machined to accept the early V8 carbs. While they do look impressive they can also deliver a good bit of fuel. For stock engine applications you are better off sticking with a single downdraft style of intake. Aluminum. U.S.A.
Specifically designed to be used with the factory radiator fan. Allows the use of a modern alternator while retaining your cooling fan in stock position.
DIMENSIONS: 5-1/2" Overall Diameter, 1-5/8" O.D, 1-3/8" I.D., 5" Tall

Single Groove Flathead Pulley Flathead Motor Mounts - Weld In Frog Mouth Scoop
Frog Mouth Scoop
Our Price: $22.50
DIMENSIONS: 5" Diameter, 1-1/4" I.D., 1-5/8" O.D.

Produced by Pete & Jakes. One of the easiest ways to mount a flathead motor in virtually any application.

Chrome plated - fits carburetors with 2-5/8" neck like 97s or 94s. These are heavy duty and beautifully chrome plated.

MOON Chopper Bung 1928-1966 Chevy Sprocket Gas Cap Finned Fuel Filter - Left to Right Fuel Flow
MOON Chopper Bung
Our Price: $12.00

Tank bungs are available in steel or aluminum.

Boldly designed gas cap - a striking addition to our well received "Sprocket" series. Machined from high grade aluminum and polished to show quality standards.

At last, fuel filters that are not just functional, but good looking also. Included is a permanent washable stainless mesh filter that should last a lifetime. Very compact in size, the bowl is 2.4" in diameter. Total height and width are 4-1/4", and projection from surface is 3". Inlet and outlet ports utilize ORB/AN-6 fittings to reduce the bulk of hose connections. Drilled for 5/16" mounting hardware - not included. Available in polished and satin finishes.

Double Remote Brake Fluid Reservoir Polished Bug Horn For 2BBL Velocity Stack Polished
Velocity Stack Polished
Our Price: $75.00

You don't have to settle for a plastic or billet reservoir. This is a real focal point little jewel. This double chamber reservoir is precision cast in aircraft grade A-356 aluminum and, polished to show grade standards. You can run the fluid lines from the bottom or backside, expanding your mounting possibilities. This product features the stunning retro style design that we have become noted for.

You don't have to settle for a plastic or billet reservoir. This is a real focal point little jewel. This double chamber reservoir is precision cast in aircraft grade A-356 aluminum and, polished to show grade standards. You can run the fluid lines from the bottom or backside, expanding your mounting possibilities. This product features the stunning retro style design that we have become noted for.

New velocity stacks for 2 barrel Stromberg, Holley and Ford carburetors. These stacks come with a Bug Dome mesh screen for insertion into your carb. Keep the bad stuff out, and look cool doing it. The finish and quality is as you have come to expect from us. We didn't invent the 2 barrel velocity stack, but we sure have improved it!

Fuel Pump Stand Flathead Power Steering Reservoir with Bracket Polished Smooth FINNED ALUMINUM BRAKE SCOOPS
Fuel Pump Stand Flathead
Our Price: $109.00

This is a new flathead fuel pump stand, comes complete with cap and gasket.

Scoops are drilled and tapped for 1/4-20 screws. We provide a drilling template for you backing plates.
4-1/2" high x 3-1/2" wide and 2" deep
Sold in Pairs- one left and one right

FINNED ALUMINUM BRAKE SCOOPS POLISHED MOON Vented Gas Cap MOON 5" Fuel Tank Brackets
MOON Vented Gas Cap
Our Price: $24.00

Scoops are drilled and tapped for 1/4-20 screws. We provide a drilling template for you backing plates.
4-1/2" high x 3-1/2" wide and 2" deep
Sold in Pairs- one left and one right

These caps are threaded to match the bungs we also sell (sold separately). These are commonly found on our aluminum tanks.

Bungs are sold separately.

Male threaded caps, female bungs.

Cast Aluminum MOON Tank Brackets for 5-inch MOON Tanks

MOON Spinner Cap Fuel Tank With Vent MOON Vented Chopper Spinner Cap & Bung MOON Chopper Spinner Cap & Bung

CAST ALUMINUM Vented Spinner Fuel Tank cap

The MOON Original Miniature Spinner Cap is similar to the vintage 50's style spinner cap but has only the raised letters for MOON. Designed to fit Chopper tanks and other tanks with a 1-1/2" chopper bung. One piece, solid cast polished aluminum crisp finish and ready for use. Comes with a 1-1/2" steel bung.

The MOON Original Miniature Spinner Cap is similar to the vintage 50's style spinner cap but has only the raised letters for MOON. Designed to fit Chopper tanks and other tanks with a 1-1/2" chopper bung. One piece, solid cast polished aluminum crisp finish and ready for use. Comes with a 1-1/2" steel bung.

MOON 3 Quart Chopper Tank MOON Junior Dragster 2 Gallon Valve Cover Gaskets
MOON 3 Quart Chopper Tank
Our Price: $259.99
Valve Cover Gaskets
Our Price: $15.00

Made in USA. Designed to mount to the frame of most motorcycles. 1/4" outlet (2) 1/4" return knurled billet cap.

Superior quality, MOON 500 series Tanks are constructed of the finest grade aluminum with MOON "SUN RAY" finish.

These valve cover gaskets are a combination rubber with metal inserts and are therefore reusable. Price is for a pair.

So-Cal Valve Cover Adapters So-Cal Alternator Bracket So-Cal Fuel Line Kit
So-Cal Alternator Bracket
Our Price: $49.95
So-Cal Fuel Line Kit
Our Price: $219.95
Machined in-house on SO-CAL's CNC mill, these small-block Chevy valve cover adapters can be used to adapt old perimeter-bolt valve covers to late-model, center-bolt heads for that traditional look. They come complete with all hardware, o-rings, etc.

This effective, single use bracket mounts a standard GM alternator to the passenger side of a small block Chevy. The bracket is offered in either plain or chrome finish.

Though designed specifically for the SO-CAL Step-Boxed ’32 Ford chassis, this fuel line kit can easily be adapted to other ’32 chassis.

Flathead Generator Fan Mount Kit Hildebrandt Finned Oil Filter Fuel Pump
Fuel Pump
Our Price: $45.00
This is a part the every flathead builder or flathead intake manifold purchaser needs. Newly made stud, square washer, and nut to mount the generator and fan pulley assembly on to any Ford or Mercury V-8 flathead intake manifold.

These filters are updated replicas of the original Hildebrandt remote oil filters.

These brand new aluminum fuel pumps were originally made by the French military to be put on service vehicles.
Champion Spark Plug 1938-1953 Ford Champion Spark Plug 1932-1937 Ford Stage 1 Block
Stage 1 Block
Our Price: $3,399.99
These Champion Copper Plus spark plugs are a direct replacement for your 1938-1953 Ford flathead V8. These Champion Copper Plus spark plugs are a direct replacement for your 1938-1953 Ford flathead V8.
The perfect Ford-Mercury block! Outstanding casting quality thanks to modern foundry technology.
Stage 2 Block Stock Rod 7" Set of 8 3-3/4" Crankshaft
Stage 2 Block
Our Price: $4,599.99
Stock Rod 7" Set of 8
Our Price: $279.00
3-3/4" Crankshaft
Our Price: $399.00
The perfect Ford-Mercury block! Outstanding casting quality thanks to modern foundry technology.
These new 8BA-style connecting rods are:
Manufactured to strict Mil-Spec standards.
Bushed, sized, straight, and true – ready to run.
Weight-difference range of about 3 grams throughout the set.
Save time and money for rebuilds as well as hop-ups.
At our price, they are cheaper than the cost of having an old set of rods mag’d, straightened, resized, and rebushed.

Applications
1949-1953 Ford car
1948-1953 Ford truck
1949-1954 Canadian truck
1949-1953 Mercury car

New 3-3/4-inch-stroke cast crankshaft. Quality Mil-Spec casting. Uses 8BA-type locked-insert bearings and rods.
Applications:
1939-1953 Ford car and truck
1939-1948 Mercury
All French
In stock and ready to ship. Truck shipping required. Rate quoted upon order.
Steel Motor Mounts Small Block Chevy S/S Motor Mounts Ford Aluminum Motor Mounts
Steel Motor Mounts
Our Price: $64.99
Ford Aluminum Motor Mounts
Our Price: $194.95

SO-CAL carries a wide variety of motor mounts both the weld-on and bolt-on types for a wide variety of applications. Price is for a pair of TWO (2).

Even though this pair of motor mounts is designed to accommodate a small block Chevy into a '32 and '33/'34 Ford chassis, we use them as universal mounts for almost anything including mid-50's shoe box cars.  They are investment cast 17-4 S/S and come with trim-to-fit weld on frame mounting tabs.

This pair of mounts accommodates both Windsor and Cleveland engines for '32 and '33/'34 Ford chassis. They are CNC machined from 6061 Aluminum alloy and come with trim-to-fit weld on frame mounting tabs.

Small Block Chevy Aluminum Motor Mounts 1947-55 CHEVY & GMC 1 SERIES TRUNK HOOD HINGE & SUPPORT SET MOON Pressure Gauge 0-100 LBS Liquid

Even though this pair of motor mounts is designed to accommodate a small block Chevy into a '32 and '33/'34 Ford chassis, we use them as universal mounts for almost anything including mid-50's shoe box cars.  They are investment cast 17-4 S/S and come with trim-to-fit weld on frame mounting tabs.

Heavy duty steel reproduction of original hood hinge style
Fits 1947-55 Chevy & GMC 1st Series Trucks
Includes hood support arm with clock spring
Black EDP coated finish
Sold as a set. Includes driver and passenger sides

WARNING: Cancer and reproductive harm

www.p65warnings.ca.gov
Direct mount liquid filled 0 - 100 lb Pressure Gauge measures 1 3/4" diameter with a 3/8" male fitting on the back.

MOON Pressure Gauge 0-15 LBS Liquid MOON Pressure Gauge 0-60 LBS Liquid MOON Breather Right Angle
MOON Breather Right Angle
Our Price: $48.00
Direct mount liquid filled 0 - 15 lb Pressure Gauge measures 1 3/4" diameter with a 3/8" male fitting on the back.

Direct mount liquid filled 0 - 60 lb Pressure Gauge measures 1 3/4" diameter with a 3/8" male fitting on the back.

Made in USA. Made to clear all linkages when installed intake side of valve cover.